Graceful Sterling Silver Rectangle Wire,Hollow Rubber Tube, and Turquoise Earrings(jewelry tutorial)




Sterling Silver Crescent and Bead Earrings

Products Necessary
three" four x one mm sterling silver rectangle wire
20-one 'Λ* head pins
Two turquoise disc beads
1 Vi* 1.7 mm black hollow rubber tube
Two sterling silver ear wires
What suggestions would you give a commencing artist?
“Do Anything you love. Discover various media. Market on the selective, constrained, foundation at the beginning to check out what is effective or what doesn't work for you before you jump into A significant outlay of cash and effort.*
-Sally J. Phillips Jewelry Designer
Equipment Essential
Ruler
Marker
Jeweler's noticed or tin snips Basic safety Eyeglasses Really hard, flat area Awl
Hammer /is" drill little bit
Hand-held rotary Software, flex shaft, or drill push File
Great grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Scissors
Wire cutters or tin snips Spherical nose pliers


one.Utilize the ruler to evaluate and mark two one Vi’ parts of four x one mm rectangle sterling silver wire.
2Using a jeweler's observed or tin snips, cut the four x one mm rectangle sterling silver wire into two one Vi’ lengths.
three.File each end of the 1Vi" rectangle wire pieces to remove any burs or rough edges.
If desired, You should use the file to round the ends of the rectangle wire pieces. Use a fine grit sanding pad to go over the area where you have submitted to sleek the sides and take away any file marks.
four.Make use of the ruler to evaluate and mark /*." from one particular conclude on the one Vi’ items of rectangle wire and spot a mark in the center in the wire. This is where you'll drill the holes to slide the head pins through.
five.Set on the protection Eyeglasses!!! Area the 1 Vi" rectangle wire items onto a hard, flat surface. Place The purpose of your awl to the mark you designed Vm,' from one particular conclude on the rectangle wire items, and firmly strike when on the top of the awl with a hammer. This could make a pilot gap for drilling holes in the rectangle wire.

Sterling Silver Crescent and Bead Earrings
Chapter five

6.Using a /is" drill bit. drill holes into a person conclusion with the rectangle wire items using a handheld rotary Instrument, flex shaft, or drill press (though continue to carrying your basic safety Eyeglasses!).
7.Use the Men's Rings file or great grit sanding pad to reduce any burs or tough edges still left from drilling holes in to the rectangle wire pieces.
eight.Curve both equally 1W items of rectangle wire into a “C" shape employing a ring mandrel and rawhide mallet. If you don't have a ring mandrel and rawhide mallet, use two pair of chain nose pliers. Keeping just one set of pliers in Each and every hand, grasp Every end of your one Vi* rectangle wire piece With all the pliers and gently bend mens ring the rectangle wire right into a “C* condition. Assess each of the C-formed rectangle wire items and modify the curves so that they are identical in si2e. Established these Men's Rings aside.
9.Utilize the ruler to evaluate and mark the rubber tube into four equivalent items mens ring measuring Vm’ Each and every. Use scissors to cut the rubber tube.
ten.Area the turquoise disc Men's Rings bead onto the head pin and insert one particular V·' piece of the rubber tube, put The pinnacle pin throughout the hole during the C-formed rectangle wire, after which add one other V«" piece of rubber tube.

13. Keep The top pin Using the bead, rubber tube, and the rectangle wire on it in a single hand With all the wire that you bent pointing towards you. Using the round nose pliers, grip the top of The top pin wire that is pointing towards you and roll it from you (think of turning the ignition critical to begin your car). Launch the pliers from The top pin wire.
At this stage, the opening while in the loop at the very best of The pinnacle pin wire need to nonetheless be significant ample to slip the ear wire on. When you incorporate the ear wire, use the spherical nose pliers to grasp the loop of the head pin wire and roll it shut. You need to use the round nose or chain nose pliers to regulate the shape of your loop at the very best of the head pin if you'll want to.
11. Utilize the ruler to measure and mark /(.’ higher than the highest piece of the hollow rubber tube. Along with the wire cutters or tin snips, Lower The pinnacle pin wire Yu.’ previously mentioned the top with the hollow rubber tube.
12. Utilize the chain nose pliers to bend the head pin wire beside the very best of your rubber tube in a 90-diploma angle.
14. Repeat these methods for the second earring.







 

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Graceful Sterling Silver Rectangle Wire,Hollow Rubber Tube, and Turquoise Earrings(jewelry tutorial)”

Leave a Reply

Gravatar